The following laboratory test results for Atterberg limits and sieve-analysis were obtained for an inorganic soil. [6 points] Sieve analysis Sieve Size No. 4 (4.75 mm) No. 10 (2.00 mm) No. 40 (0.425 mm) No. 200 (0.075 mm) Percent passing by weight 80 60 30 10 Atterberg limits Liquid limit (LL) Plastic limit (PL 31 25
(a) Classify this soil according to USCS system, providing the group symbol for it. Show how you arrive at the final classification.
(b) According to USCS system, what is a group name for this soil?
(c) Is this a clean sand? If not, explain why.
Answers
Answer: hello the complete question is attached below
answer:
A) Group symbol = SW
B) Group name = well graded sand , fine to coarse sand
C) It is not a clean sand given that ≤ 50% particles are retained on No 200
Explanation:
A) Classifying the soil according to USCS system
( using 2nd image attached below )
description of sand :
The soil is a coarse sand since ≤ 50% particles are retained on No 200 sieve, also
The soil is a sand given that more than 50% particles passed from No 4 sieve
The soil can be a clean sand given that fines ≤ 12%
The soil can be said to be a well graded sand because the percentage of particles passing through decreases gradually over time
Group symbol as per the 2nd image attached below = SW
B) Group name = well graded sand , fine to coarse sand
C) It is not a clean sand given that ≤ 50% particles are retained on No 200
Related Questions
(2pts) In _______________, the pulse amplitude is made proportional to the amplitude of the modulating signal. pulse-amplitude modulation (PAM) pulse-position modulation (PPM) pulse-code modulation (PCM) pulse-width modulation (PWM)
Answers
Answer:
(a) pulse-amplitude modulation (PAM)
Explanation:
It should be no surprise that pulse amplitude is modulated in pulse-amplitude modulation (PAM).
Label the following statements as either T (true) or F (false).
1) For Propane (C3H8) burning with theoretical amount of air, the air-fule ratio on the mole basis is 5.
2) The enthalpy of any substance at the standard reference state is 0.
3) 180% of theoretical air is equivalent to 80% of excess air.
4) The conservation of mass principle requires that the total number of moles on each side of a chemical reaction is equal.
5) The adiabatic flame temperature of methane (CH4) burning with pure oxygen and theoretical amount of air is the same, all other conditions being the same.
Answers
Answer:
1 its 1 bc you have to do it step by step
Explanation:
step by step
Two students are discussing weathering and erosion factors. Leah says that both weathering and erosion involve wind, water, and ice. Justin says that only weathering involves ice, and that erosion involves plants and animals. Who is correct?
A. Justin, because plants cause erosion too.
B. Justin, because erosion does not involve ice.
C. Leah, because she forgot to mention plants and animals.
D. Leah, because glaciers are ice that cause erosion too.
Answers
Answer: Justin is false and it is both bottom because plants and animals are helpless to erosion and we cause it by deforestation and weather does too
Explanation:
Justin, because plants cause erosion too factors. This was the statement are the correct. Thus, option (a) is correct.
What is erosion?The geological process through which earthen elements are worn down and transferred by wind and water or water is known as erosion. The migration of nanoparticles away from their origins is referred to as erosion. Erosion is the loss of dirt, rock, or dissolved substances by surface processes.
According to the two students are the different in the studies. There was the based on the Leah are the said on the different in the concept and the Justin said into the different in the concept are the perception of the topic are the different. Justin was the correct because plants are the cause of erosion too factors.
As a result, the Justin, because plants cause erosion too factors. Therefore., option (a) is correct.
Learn more about on erosion, here:
https://brainly.com/question/3852201
#SPJ2
Find the mean deviation of the set of numbers
(a) 12, 6, 7, 3, 15, 10, 18,5
Answers
Answer:
4.25
Explanation:
The mean deviation is how far, on average, all values are from the middle. To do that, we subtract each element from the mean of the elements, take their absolute values, and then divide by the number of elements in the set. Here's the formula: [tex]\sum\frac{|x-\mu|}{n}[/tex]
Here the mean is 9.5, the count n = 8, so the mean deviation is 4.25
Why is the tensile strength of a material important to consider when building a structure? Answer in a one page essay!!!
Answers
The theory began with the consideration of the behavior of one and two dimensional members of structures, whose states of stress can be approximated as two dimensional, and was then generalized to three dimensions to develop a more complete theory of the elastic and plastic behavior of materials. An important founding pioneer in mechanics of materials was
HELP HELPHELP HELPHELP HELPHELP HELPHELP HELPHELP HELPHELP HELPHELP HELPHELP HELPHELP HELPHELP HELPHELP HELPHELP HEL
Answers
Answer:
oh this happened with me to ,this will be alright just wait a bit
The section 5(a)(1) of the osh act is commonly known as
Answers
Answer:
general duty clause
Explanation:
Create a Python script that will compare two (2) numbers entered by the user. Refer to the attached image and to the following algorithm. There is no need to create a class similar to how Java works.
3.1. User enters the first number.
3.2. User enters the second number.
3.3. If the first number is less than, greater than, or equal the second number, a message is displayed.
Please Help me. Thank You!
Marry Christmas!
Answers
Answer:
number1 = input("Choose a first number: ")
number2 = input("Choose a second number: ")
if number1 >= number2:
print("Number 1 is greater")
a. State the functions of the followings
a. Commutator
b. Armature core
c. Field system
d. Brushes
e. Armature winding
Answers
Answer:
a. State the functions of the followingsa. Commutator:
the commutator reverses the current direction with each turn serving as a mechanical rectifier to convert the alternating current from the windings to unidirectional direct current in the external load circuit.
b. Armature core
Armature core is a physical structure made up of silicon steel stampings. The core is laminated to keep iron losses low. Armature winding is the main current carrying winding where we either provide(electric supply to motor) or extract e.m.f(collect electric power from generator).
c. Field system
The field winding basically form an electromagnet, that produces field flux within which the rotor armature of the DC motor rotates, and results in the effective flux cutting
d. Brushes
The function of brushes is that the brushes conduct current between stationary wires and moving parts of the electric Generator.
e. Armature winding
The winding wound on the core is given current through a DC supply. This current-carrying winding as under the influence of the magnetic field develops a force that develops a rotational torque. This torque enables the machine to rotate.
[tex] \bold \pink{ \underline{hope \: it \: helps}}[/tex]
how many times greater is the value of the 2 of the 270413 than the valuce of the 2 in 419427?
Answers
Step-by-step explanation:
The value of 2 in 270,413 is 200,000.
The value of 2 in 419,427 is 20
Divide the two numbers together to find your answer:
200,000/20 = 10,000
The value of 2 in 270,413 is 10,000x greater than the value of 2 in 419,427.
Please mark it as brainlest answer:).
Over 30 day period, a lake surface area is 1260 acres. The inflow is 36 cfs, thee outflow is 30 cfs. Seepage loss is 1.5 in. The total precipitation is 4.0 in. Evaporation loss is 6.0 in. Determine the water level change (inch) for the lake during this period.
Answers
Answer:
-0.1 inches
Explanation:
The net inflow is ...
36 cfs -30 cfs = 6 cfs
The number of seconds in 30 days is ...
(3600 s/h)(24 h/da)(30 da) = 2,592,000 . . . . seconds/(30 days)
Then the volume of inflow is ...
(6 ft^3/s)(2,592,000 s) = 15,552,000 ft^3
The number of square feet in 1260 acres is ...
(1260 ac)(43560 ft^/ac) = 54,885,600 ft^2
So, the increase in depth due to the inflow is ...
(15,552,000 ft^3)/(54,885,600 ft^2) ≈ 0.283353 ft ≈ 3.4002 in
__
The net change in water level is then ...
inflow - seepage + precipitation - evaporation
3.4 in -1.5 in +4.0 in -6.0 in = -0.1 in
The water level change in the period is -0.1 inch.
Marketing in the fresh produce industry does not include buying, selling,
transportation or pricing?
Answers
Answer: I personally believe it does, because the Circle of Life, or what I think, at least buying and selling
Explanation:
Help! Please explain also. Thank you
Answers
Answer:
17A) 52mm
17B) 132mm
17C) 67mm
18.) 34
Explanation:
For 17)
Each distance is determined by the total distances surrounding it. For example, 17A is 73mm - 21mm, which is 52mm.
For 18)
Set up the problem as an algebraic expression:
a + b + c + d = 115
Since you know 3 of the values, you can plug them in and subtract them from 115, which turns into 34.
openings around pipes that enter building should be covered by
Answers
Answer: I have 2 suggestions: one, maybe, maybe, use some of that metal tape that you get at hardware places, and: two, buy a new pipe (or pipes), two be sure that it won't happen again. Have a good day, and thanks for asking the brain!
Explanation:
A computer feedback fuel system has poor driveability when cold. Technician A says
that this could be due to a bad oxygen sensor. Technician B says to check for
external causes such as an intake manifold leak or incorrect fuel system pressure.
Who is correct?
Technician A
Technician B
Both A and B
Neither A nor B
Answers
Answer:
B is correct I believe
need help answering this question
Answers
Answer: Wow. I just did that not so long ago. The mean is 76, i think the deviation is 73 and ill recall my notes for the next, hold on
Explanation:
Write a program that computes the square footage of a house given the dimensions of each room.Have the program ask the user how many rooms in the house and then request the dimensions of eachroom. Display the resulting total square footage.
Answers
int main () {
printf("Program to calculate the square footage of the house.\n");
int total_rooms;
double length, width;
double total_square_footage = 0.0;
printf("Enter total number of rooms in the house:");
scanf("%d", &total_rooms);
for (int i = 0; i
printf("Enter the lenght and width of room %d: ", i+1);
scanf("%if %if", &lenght, &width);
total_square_footage += lenght*width;
}
printf("Total square footage of the house: %if\n", total_square_footage);
return 0;
}
Please mark it as brainliest answer:).
Explain the conditions under which galvanic corrosion occurs
Answers
Answer:
Explanation:
Galvanic corrosion occurs when two dissimilar metals are immersed in a conductive solution and are electrically connected. One metal (the cathode) is protected, whilst the other (the anode) is corroded. The rate of attack on the anode is accelerated, compared to the rate when the metal is uncoupled.
A fully charged battery with 6 cells should indicate
Answers
Answer:
Battery Voltage
Voltage refers to the amount of electrical potential your battery holds. The standard automotive battery in today's vehicles is a 12-volt battery. Each battery has six cells, each with 2.1 volts at full charge. A car battery is considered fully charged at 12.6 volts or higher.
The part of the circuit that converts electrical energy into other forms
Answers
Answer:
Alternator
Explanation:
A device which converts mechanical energy into electrical energy.
I hope it helps.
Question 2 Given the following gas Volume (%) Component Methane 58.7 Ethane 16.5 9.9 Propane Butanes 5.0 Pentanes 3.5 Hydrogen Suflide 6.4 100 Total I Calculate: 1. Average molecular weight 1. Density at 320F and 14.7 psia ni. Density at OoC and 760 mm mercury iv. Specific gravity and gross and net heating value
Answers
Answer
I think 51.96 I hope it's help
10. Which is of the following is not used in the
testing/analysis step?
A. Engineering notebooks.
B. Multiview drawings.
C. 3-D modeling software.
D. CNC machines.
Answers
A CNC machine stands for Computer Numerically Controlled Machine, they are used to Machine objects in hence create items, machine parts from prototypes. Hence the CNC machines are not used for testing/Analysis
D. CNC machines.
In Engineering the following items are basically needed for and during test/Analysis
Engineering notebooks: This is used to write down importance observations and findingsMulti-view drawings: This is also needed to visualise prototypes from different perspective or views3-D modelling software: e.g AutoCad , Autodesk Inventor, Revit to mention a few can be used to design and analyse project even before their actual implementation or designLearn more:
https://brainly.com/question/9275741
What effect did the Ice Age have on early humans
Answers
Answer:
The development of homosapiens
Explanation:
People adapted to the harsh weather by creating tools and used land bridges to spread to new regions
An airline ticket counter forecasts that 220 people per hour will need to check in. It takes an average of 2 minutes to service a customer. Assume that arrivals are poisson distributed and service times exponentially distributed and that customers wait in a single queue for the first available agent.
a) If we want the average time a customer spends in the queue and in service to be 10 minutes or less, how many ticket agents should be on duty?
b) There airline wants to minimize the cost of idle ticket agents and the cost of customers waiting in the queue. The salary of a ticket agent is £12 per hour and the cost of a customer waiting in the queue is £5 per customer per hour. How many ticket agents should be on duty?
Answers
A) Number of agents required to achieve a wait time of 10 minutes or less = 8 agents
B) The number of agents required on duty to reduce cost = 9 agents
Given data :
Arrival rate of customers ( β ) = 220 per hour
Service rate ( mu ) = 60 minutes / 2 minutes = 30 customer per hour
utilization ( rho ) = 220 / 30 ≈ 7
at least 8 server personnel are required for stability of the queue
A) Determine the number of agents required to achieve a wait time of 10 minutes or less per customer
waiting time = 10 - 2 = 8 minutes
number of customers waiting ( ∝ ) = 7 and required server = 8
assuming Lq = 5.2266
Hence the waiting time in line = Lq / arrival rate
= 5.2266 / 220 = 0.0238 hour
= 0.0238 * 60 = 1.428 minutes
Since the waiting time ( 1.428 minutes ) is less than the original waiting time ( 2 minutes ) the number of agents that will achieve a wait time of 10 minutes or less is = 8 agents
B) Determine the number of ticket agents that should be on duty to minimize cost
salary of ticket agent = £12 per hour
cost of customer waiting in queue = £5 per hour per customer
i) When 8 agents are used
waiting time of customers = 0.0238 * 220 = 5.236
waiting cost for customers = 5.236 * 5 = £26.18
employee cost = 8 * 12 = £96
∴ Total cost = 96 + 26.18
= £ 122.18
ii) When 9 agents are used
waiting time for customers = 0.0074 * 220 = 1.628
Wq = 1.6367 / 220 = 0.0074
waiting cost for customers = 1.6367 * 5 = £ 8.1835
assuming Lq = 1.6367
employee cost = 9 * 12 = £ 108
∴ Total cost = 108 + 8.1835 = £ 116.18
From the calculations in ( i ) and ( ii ) the Ideal number of ticket agents that should be on duty to minimize cost should be 9 agents.
Hence we can conclude that A) Number of agents required to achieve a wait time of 10 minutes or less = 8 agents and The number of agents required on duty to reduce cost = 9 agents.
Learn more about cost reduction : https://brainly.com/question/14115944
How can we honor what we value and care about in a world of disruptive technologies like AI?
Answers
Answer: Well, that's a good question. When we look around us, we tend to see what technology has done for us, and how far it is taking us. It might be disruptive, but without it there would be no high tech military weapons, and then how would we defend ourselves? There would be no technology entertainment and without that, life would be very dull. In answering your question, we can be thankful for what it is and how far it has been taking us in life.
Explanation: Please mark a brainliest if correct it helps and have meery holidays!
What is the first step in the decision-making process?
Answers
Answer: identify your decision. relize you need to make a decision.
Explanation:
6.03 Discussion: Then & Now - Safety
Discussion Topic
I'm Done
In this unit, you have learned about the evolution of the industry’s machines, through both technology and innovation. These improvements have reduced risk and injury to the Operating Engineers.
Choose one innovation or device.
Explain why you think that technology is the most important advancement in Operating Engineers’ safety.
Answers
Answer:
Information technology is important in our lives because it helps to deal with every day's dynamic things. Technology offers various tools to boost development and to exchange information. Both these things are the objective of IT to make tasks easier and to solve many problems.
I need help finding a good selling for a 71 Ford mustang hardtop coupe price This isn't really a school question but it's the only place I know we're I can ask questions so I'll give it a go
Answers
Answer:
you know you could use like quora or yahoo answers
Class 0 rubber gloves are used when working with voltage less than
Answers
Class 00 rubber gloves are given the color "beige" based on the color code of rubber gloves.
The proof test voltage for this class of rubber gloves is 2500 volts of AC voltage and 10000 volts of DC voltage
Please mark it as brainliest answer:).
4. What is the ampacity of 8-gage copper wire?
O A. 45 amps
OB. 30 amps
O C. 50 amps
O D. 25 amps
