Answer:
Though pitch and frequency are not equivalent, they are correlated. This means that as one goes up, the other does as well. A higher frequency produces a higher pitch, and a lower frequency produces a lower pitch.
Explanation:
a new planet is discovered that has twice the earth’s mass and twice the earth’s radius. on the surface of this new planet, a person who weighs 500 n on earth would experience a gravitational force of
Answer: 250n
Explanation:
The formula for gravitational force is: F = (gMm)/r^2
There are two factors at play here:
1) The mass of the planet 'M'
2) The radius 'r'
We can ignore the small M and the g, they are constants that do not alter the outcome of this question.
You can see that both M and r are double that of earth. So lets say earth has M=1 and r=1. Then, new planet would have M=2 and r=2. Let's sub these two sets into the equation:
Earth. F = M/r^2 = 1/1
New planet. F = M/r^2 = 2/4 = 1/2
So you can see that the force on the new planet is half of that felt on Earth.
The question tells us that the force on earth is 500n for this person, so then on the new planet it would be half! So, 250n!
White light is an _____ mixture of all the colors.
Answer:
White light is a combination of all colors in the color spectrum.
Explanation:
It has all the colors of the rainbow. Combining primary colors of light like red, blue, and green creates secondary colors: yellow, cyan, and magenta
A balloon is rubbed against a sweater. Which of the following describes the result of this interaction?(1 point)
The outer shell electrons move from the balloon to the sweater.
The fibers of the sweater lose electrons.
The balloon becomes positively charged.
The free electrons in the balloon decreases.
Answer:
The fibers of the sweater lose electrons.
What is the anomalous expansivity of water
Answer:
The anomalous expansion of water is an abnormal property of water whereby it expands instead of contracting when the temperature goes from 4o C to 0o C, and it becomes less dense. The density is maximum at 4 degree centigrade and decreases below that temperature as shown in graph.
Explanation:do you want me to explain it more??
**BRAINLIEST** How does the Combining Vinegar and Baking Soda table represent the law of conservation of matter when baking soda and vinegar are combined?
Basically your liquid will go over the line because you are adding more mass. the balloon will inflate because of mass filling it. Part 1 I noticed that there was a change from the original line. part 2 Some mass is lost. The bubbles are the gas leaving. The balloon increases in size because of the mass. The cup got heavier when I added the vinegar.
Gas leaving caused the bubbles.
I keep people warm I come in many different colors, styles, and materials. many people use me when they sit on a couch
Answer:
a seat
Explanation:
The phrase “seat value” is used in the hospitality and bar sectors to describe how much money each seat or square foot of customer area must generate to justify its existence.
What is the use of seat by the people?An area to sit is a seat. The phrase may also refer to headquarters in a more general meaning as well as extra elements such a back, armrest, and head restraint.
Being in the centre allows you to benefit from both the advantages of both front and back seating while balancing out their extremes. While you're still close enough to be paying careful attention to the lecture, the middle rows will relieve you of the pressure and expectations of the front.
By remaining seated, students help avoid physical altercations. There is more time spent on task when pupils are seated.
Environmental psychology, which gives people the impression that they have some degree of influence over their daily lives, is the driving force behind all of this behavior.
Therefore, seat used by people.
Learn more about seat here:
https://brainly.com/question/19261993
#SPJ2
Other than temperature, which property also has an effect on the rates of chemical reactions?
A.Color of reactants
B.Concentration of reactants
C.Solubility of reactants
D.Volume of reactants
Other than temperature, the property that also has an effect on the rates of chemical reactions is the concentration of the reactants. The correct answer is B
The rate of chemical reaction means how chemical react with respect to time or as a function of time. The rate of chemical reaction tells us the speed or how fast chemicals react.
There are many factors that can affect the rate of chemical reaction. Temperature is one of them. Increase in temperature will increase the rate at which chemical react.
The color of reactants, solubility of reactants and volume of reactants have nothing to do with the rate of chemical reaction.
Other than temperature, the property that also has an effect on the rates of chemical reactions is the concentration of the reactants.
Other factors affecting the rate of chemical reaction are:
the physical state of the reactants surface area temperature and the presence of a catalystTherefore, the correct answer is option B
Learn more about chemical reaction here: https://brainly.com/question/11231920?source=archive
please someone help me understand this question
[tex]\\ \sf\longmapsto F=\dfrac{Gm_1m_2}{r^2}[/tex]
m1 and m2 has same units let both be m[tex]\\ \sf\longmapsto F=\dfrac{Gm^2}{r^2}[/tex]
[tex]\\ \sf\longmapsto G=\dfrac{Fr^2}{m^2}[/tex]
SI units:-
F=Newton (N)r=metre(m)mass=m=kg[tex]\\ \sf\longmapsto G=\dfrac{Nm^2}{kg^2}[/tex]
Option C is correct
1. The law of reflection states that the angle of _______ is equal to the angle ofreflection
•refraction
•incidence
Answer:
refraction
Explanation:
but this is easy so why
A young diver is practicing his skills before an important team competition. Use the diagram below in order to analyze the energies of the diver and complete the statements below.
Where m = mass (kg), g = 9.8 m/s2, v = velocity (m/s), h = height (m), KE = kinetic energy (J), and GPE = gravitational potential energy (J).
Use the equations above to answer the following questions.
A diver with a mass of 90 kg is at a height of 10 m, and he has not jumped off of the board yet (v = 0 m/s). When the diver reaches a height of 5 m (Point C), his gravitational potential energy is
A. 1350 J
B. 8820 J
C. 4410 J
D. 0 J
and his velocity is
E. 4.5 m/s
F. 0 m/s
G. 3.2 m/s
H. 9.9 m/s
Please help will mark brainliest
Answers:
The gravitational potential energy of the diver when he reaches point C is 4410 J.
The velocity of the diver is 9.9 m/s.
Hope you could get an idea from here.
Doubt clarification - use comment section.
[tex]\\ \sf\longmapsto PE=mgh[/tex]
[tex]\\ \sf\longmapsto PE=90(5)(9.8)[/tex]
[tex]\\ \sf\longmapsto PE=4410J[/tex]
Now
It's converted to kinetic energy while reaching ground.
[tex]\\ \sf\longmapsto K.E=4410[/tex]
[tex]\\ \sf\longmapsto \dfrac{1}{2}mv^2=4410[/tex]
[tex]\\ \sf\longmapsto 90v^2=8820[/tex]
[tex]\\ \sf\longmapsto v^2=98[/tex]
[tex]\\ \sf\longmapsto v=9.9m/s[/tex]
please help quick
How much work is done by the people in raising the load 3 meters if the combined pulling force of the men on the rope is 700 newtons?
A.233 N·m
B. 703 N·m
C. 2,100 N·m
D. 400 N·m
Answer:
C is the right answer for the question
An object, moving with a constant velocity, travels 400 m in 25 s. What is its velocity?
v = d/t
= 400/25
= 16 m/s
I'm not sure though
Please help someone. A generator consumes 147 joules of energy in fuel and produces 75 joules of energy
in electricity. Engineers are challenged to produce a generator that is 20% more
efficient. Which of the following combinations of input and output energy represents a generator that has met this design challenge?
a. 150 joules of fuel to produce 90 joules of electricity
b. 135 joules of fuel to produce 68 joules of electricity
c. 60 joules of fuel to produce 100 joules of electricity
d. 115 joules of fuel to produce 82 joules of electricity
Answer:
A
Explanation:
Current effiency
= 75/147
= 0.5102
New Efficiency
= 120/100 × 0.5102
= 0.6122
Only option A satisfies this efficiency.
Use what you know about mass and how you use it to calculate force in the following situation. If each washer has a mass of 4. 9 g, then the mass of two washers in kilograms would be. Given that F = ma, and if 4 washers are attached to the string and car instead of 2, then the applied force on the car will be. Recall a = 10 m/s2.
Considering the change of units and the definition of weight, the mass of two washers would be 0.0098 kg and if 4 washers are attached to the string, then the applied force on the car will be 0.196 N.
Mass of two washers
If each washer has a mass of 4.9 g, then the mass of two washers will be calculated simply by multiplying the mass of 1 washer by the amount you have of them, in this case 2:
4.9 g×2= 9.8 g
Being 1 kg = 1000 g, you apply the following rule of three to make the change of units: if 1000 g equals 1 kg, 9.8 g equals how many kilograms?
[tex]mass=\frac{9.8 gramsx1 kg}{1000g}[/tex]
Solving:
mass= 0.0098 kg
Finally, the mass of two washers would be 0.0098 kg.
Applied forceOn the other side, mass is the amount of matter that a body contains and weight is the action exerted by the force of gravity on the body.
The mass of an object will always be the same, no matter where it is located. Instead, the weight of the object will vary according to the force of gravity acting on it.
Weight is calculated as the product of the object's mass and the value of the gravitational acceleration:
W= m×g
In this case, you know:
m= 4.9 g×4= 19.6 g= 0.0196 kg → the mass of 4 washers in kilogramsg= 10 m/s²Replacing:
W= 0.0196 kg× 10 m/s²
Solving:
W= 0.196 N
Finally, if 4 washers are attached to the string, then the applied force on the car will be 0.196 N.
Learn more:
brainly.com/question/15566515?referrer=searchResults brainly.com/question/15271930?referrer=searchResults brainly.com/question/4735812?referrer=searchResultsAnswer:
C, B
Explanation:
car was moving in a straight road of length 320 km it covered 240 km with an average velocity 75 km/hr then it ran out of fuel and stopped for 0.6 hr until it was refueled and completed its journey with a velocity 100 km/hr so the average velocity during the whole journey
The average velocity of the car for the whole journey is 69.57 km/h.
The given parameters:
Length of the road, L = 320 kmDistance covered = 240 km at 75 km/htime spent refueling, t₂ = 0.6 hrFinal velocity, = 100 km/hrThe time spent by the before refueling is calculated as follows;
[tex]t = \frac{d}{v} \\\\t_1 = \frac{240}{75} \\\\t_1 = 3.2 \ hours[/tex]
The time spent by the car for the remaining journey;
[tex]t_3 = \frac{320 - 240}{100} \\\\t_3 = 0.8 \ hr[/tex]
The total time of the journey is calculated as follows;
[tex]t = t_1 + t_2 + t_3\\\\t = 3.2 \ hr \ + \ 0.6 \ hr \ + \ 0.8 \ hr\\\\t = 4.6 \ hours[/tex]
The average velocity of the car for the whole journey is calculated as follows;
[tex]v = \frac{total \ distance }{total \ time} \\\\v = \frac{320}{4.6} \\\\v = 69.57 \ km/h[/tex]
Learn more about average velocity here: https://brainly.com/question/6504879
Solve the science problem
A circle has a radius of 10 inches. Find the approximate length of the arc intersected by a central angle of mc001-1. Jpg 6. 67 inches 10. 47 inches 20. 94 inches 62. 8 inches.
The approximate length of the arc intersected by the central angle is 20.94 inches.
The given parameters:
Radius of the circle, r = 10 inchesCentral angle, [tex]\theta = \frac{2\pi }{3} \ rad[/tex]The approximate length of the arc intersected by the central angle is calculated as follows;
S = rθ
where;
S is the length of the arcSubstitute the given parameters and solve for the length of the arc
[tex]S = 10 \ in \times \frac{2\pi }{3} \\\\S = 20.94 \ inches[/tex]
Thus, the approximate length of the arc intersected by the central angle is 20.94 inches.
Your question is not complete, find the complete question below:
A circle has a radius of 10 inches. Find the approximate length of the arc intersected by a central angle of [tex]\frac{2\pi}{3}[/tex].
Learn more about length of arc here: https://brainly.com/question/2005046
Jacob has a disk that sinks to the bottom when placed in a vessel of water. He cuts some holes in the disk and immerses it again in a vessel of water. Which of these is likely to happen?
Answer:
it will float up cause its has gravity
When Jacob cuts some holes in the disk and immerses it again in a vessel of water it will now float at the top. Thus, the correct option for this question is A.
Why does an object float at the top of the water?An object floats when the weight force on the object is balanced by the upward push of the water on the object. The upwards push of the water increases with the volume of the object that is underwater. It is not affected by the depth of the water or the amount of water.
According to the context of this question, when a disk does not have holes in it, it will definitely sink to the bottom of the water because it has high density, but when the hole is made in the disk, the water is passed out from them and now, the upward force is minimized that cause less density as compared to previous.
Therefore, when Jacob cuts some holes in the disk and immerses it again in a vessel of water it will now float at the top. Thus, the correct option for this question is A.
To learn more about Upward force, refer to the link:
https://brainly.com/question/24279743
#SPJ2
The force involved in falling of an apple from a tree is known as? (a) Magnetic force (b) electrostatic force (c) Contact force (d) gravitational force
Answer:
gravitational force
...........
what prevents the planets in our solar system from floating away?
A. Earth's gravitational pull
B. planets gravitational pull on one another
C. moon's gravitational pull
D. suns gravitational pull
Suns' gravitational pull prevents the planets in our solar system from floating away, therefore the correct answer is option D.
What is a solar system?It is a structure in which the sun's attractive force causes all the planetary systems and celestial bodies to revolve around this.
The Sun is believed to be located in the system's center in the sun-centered concept upon which our Solar System is founded.
The primary factor that causes the planets in the solar system to revolve around the sun is gravity.
The sun's pull of gravity prohibits the planets in our planetary system from moving away, hence option D is the appropriate
To learn more about Solar systems, refer to the link given below;
brainly.com/question/12075871
#SPJ2
1. How much energy is needed just to melt 0.56kg of ice at 0◦ C?
2. How much energy is needed just to boil 5kg of water at 100◦ C?
3. What is the specific heat of metal if its mass is 27 g and it requires 420 J of heat energy to
increase its temperature from 25°C to 50°C?
please help me out I dont have much time
Answer:
This will require 266.9 of heat energy.
Explanation:
To calculate the energy required to raise the temperature of any given substance, here's what you require:The mass of the material, m The temperature change that occurs, ΔT The specific heat capacity of the material,
c
(which you can look up). This is the amount of heat required to raise 1 gram of that substance by 1°C.
Here is a source of values of
c for different substances:
Once you have all that, this is the equation:
Q=m×c×ΔT(Q is usually used to symbolize that heat required in a case like this.)For water, the value of c is 4.186g°C So, Q=750×4.186×85=266=858=266.858
What is the minimum number of overload units such as heaters, trip coils, or thermal cutouts allowed for a three-phase AC motor's protection
The minimum number of overload units for a three-phase AC motor's protection is THREE (3). It is a polyphase motor.
Three-phase motors are polyphase motors, which can be induction motors or synchronous motors.
A three-phase motor is organized to run on three-phase alternating current (AC) electrical power, which is required for diverse industrial devices that use a lot of electrical energy.
These motors (three-phase motor) are composed of a stator (the outer part), a rotor (rotating part), and the enclosure (the external skeleton).
Learn more about three-phase motors here:
https://brainly.com/question/14329442
Va A rail wagon of mass
5000 kg moving at a velocity
of 1.6 ms-1 collides with a
stationary wagon of mass
3000 kg (see Figure 4). After
the collision, the 3000 kg wagon
moves away at a velocity of
1.5 ms-1. Calculate the speed
and direction of the 5000 kg
wagon after the collision.
Answer:
0.7m/s
Explanation:
According to the conservation of linear momentum, the moment before a collision is equal to the moment after the collision. The equation is written as follows: [tex]m_{a}u_{a} + m_{b}u_{b} = m_{a}v_{a} + m_{b}v_{b}[/tex], where [tex]m[/tex] is the mass of the object, [tex]u[/tex] is the initial velocity, and [tex]v[/tex] is the final velocity.
Let's say the object [tex]a[/tex] is our moving wagon and the object [tex]b[/tex] is our stationary wagon. [tex]m_{a} = 500kg, u_{a} = 1.6ms^{-1}[/tex], [tex]m_{b} = 3000kg, u_{b} = 0[/tex], since the wagon is stationary, it doesn't have any initial velocity. After collision, the mass remains the same, but the velocity changes: [tex]v_{a} = ?, v_{b} = 1.5ms^{-1}[/tex]
We can observe that [tex]v_{a}[/tex] is what we're looking for according to the question. Now let's substitute our values.
[tex](5000 * 1.6) + (0) = 5000v_{a} + (3000 * 1.5)[/tex]
[tex]v_{a} = \frac{(5000 * 1.6) - (3000*1.5)}{5000}[/tex] = 0.7m/s
pls help quickly
Which of these materials best scatters the light that strikes it?
a pure water
b shiny mirror
c frosted glass
d eyeglass lens
Answer: frosted glass
Explanation:
Answer:
C
Explanation:
Frosted Glass
Texting: what are two needs or wants that this wave technology meets it:
Answer:
bugs/viruses all the time and more social platforms
Explanation:
If a planet has an eccentricity of 0.92 and a distance of the major axis is 5,000,000 km, then what is the distance between foci?(1 point)
460,000,000 km
0.00000018 km
4,600,000 km
5,000,000 km
Answer:
it’s the third option: 4,600,000 km
Explanation:
just took the test and that was correct
23 and 24 only please help!
Answer:
23: Acceleration 24:1m/s^2
Explanation:
[tex]a = (v_f - v_i) /delta(t)\\a=(16-10)/6\\a=6/6\\a=1m/s^2[/tex]
How to find final velocity and initial velocity and acceleration ? :(
Explanation:
Final velocity=Initial velocity+(acceleration×time)
4 ways to find initial velocity:
1) Initial velocity=Final velocity-(acceleration×time)
2) Initial velocity=(Distance/Time)-((acceleration×time)/2)
3) Initial velocity=√Final velocity-(2×(acceleration×distance))
4) Initial velocity=2(distance/time)-Final velocity
Total force = Mass×Acceleration
(F=ma)
How many protons are in C-14?
Answer:
56 proton sir
have a nice day
The bulb in the circuit shown below does not glow. Which of following labelled parts is responsible for this?
Answer:
answer to this question is c
Answer:
3
Explanation:
because the battery's power is not functioning well
